iPhone LCD Recycling and iPhone LCD Screen Replacement: 2016

2016/12/16

2016/08/26

China has become the world's largest electronic waste factory

Every hour, your iPhone is in constant aging, will eventually become e-waste.With the development of technology and the competition, electronic waste is already the world's fastest-growing waste.According to a report by the United Nations in 2014, the world can produce about 4000 tons of e-waste per hour.These mountains of e-waste are mostly concentrated in the third world countries, and China is the worst-hit areas.Each year, more than 3 million tons of e-waste dismantling smuggled into China from all over the world, whether computers or mobile phones, monitors.

Is the high cost of backward technology, developed countries are not willing to the main reason for the recovery of electronic waste at home, but so far, e-waste recycling companies also have no better solution - perhaps, mass-produced consumer digital product of science and technology companies should take on some of the blame.

In addition to technology companies to increase investment in r&d, the government also should give support in terms of new technology.E-waste recycling is not going to solve the problem, but the environment problem continues, every family has a lot of old digital electronic products, how do you deal with the old stuff?

LCDONE, a high-tech company providing the solutions for the mobile phone broken glass screen, including iPhone LCD recycling, Samsung Galaxy LCD recycling, iPhone LCD screen repair swap, Samsung Galaxy LCD screen repair swap, iPhone LCD screen wholesale, iPad touch screen wholesale and mobile phone accessories.

We do not produce the mobile phone lcd screen, we only do recycle,repair swap and lcd screen wholesale.

Surprise, now ,register on our website https://www.lcdone.com, with the referral code: jackie20160826, you can get the free shipping for your first order.

2016/07/27

video about how to replace ipad 4 lcd screen and digitizer assembly - LCDONE

let's go ahead and start to disassemble on our iPad 4 by first feeling back our touch screen so that we can access all the internal components for replacement.

we are going to start off first with our heat gun or blow dryer and heat up the outside perimeter of our touch screen to soften up the adhesive, so that we can separate the touch screen from the base of our iPad, 1 to 2 minutes of the heat should suffice.

let's grab our plastic opening tool to begin our entry into the ipad.

we are going to work at the touch screen edge where it meets the bezel of the ipad to begin our separation.

once the plastic opening tool begins to separate that touch screen slightly and you want to work ourselves around the ipad trying to open up that separation around the entire perimeter.

with one side of that touch screen completely separated, we like to use a triangle opening tool and the separation so that the adhesive doesn't come back in contact with itself, as you continue working at that touch screen into the next side, again with that separation made.

let's use another triangle opening tool to keep that gap open. while working on the touch screen, let's be mindful of the ribbon cable that's about two inches from the bottom on the left hand side of the unit. let's be careful around this area so that we don't cause any irreversible damage.

again continuing all the way around the unit until we've got separation on all four sides leaving triangle opening tools in the gap to help keep the separation.

when you completed with the separation, we can now peel back that front touch screen almost like a book and being mindful of the ribbon cable that's still connected.

let's now work towards removing the LCD, you're going to notice held down by four Phillips screws one in each corner.

let's go ahead and remove those screws, with our four screws removed, let's lift the LCD up and out and gently resting on to the touch screen.

revealing our ribbon cable that has a locking socket into the motherboard, we want to lift the lever on that socket releasing the cable, so that we can remove it from the motherboard, and now completely remove the LCD from the ipad.

our touch screen is going to have similar locking sockets or removal, releasing two levers for the actual touch screen ribbon cable and then the smaller blocking socket for the ribbon cable for the home button assembly down towards the bottom. let's release both of these locks, and we can remove the touch screen completely from the iPad as well.

we can now go ahead and start working towards our reassembly of our iPad 4, starting with our touch screen digitizer we can maneuver it into place in a position where the ribbon cable has enough slack to find itself into the socket on the motherboard.

let's slide are whipping cables into their sockets, lockdown on their tabs and secure the ribbon wire in place, we can move on to our small home button ribbon wire, do the same situation where we're sliding our ribbon cable into the locking socket, and locking down its tab to finalize that connection. with our three connections secured for our front touch screen, we can get our LCD into position laying it on top of our touch screen again with a nut slack on the ribbon cable to reach its socket on the motherboard.

let's slide that cable into its socket and lock down its tab finalizing that connection, with the LCD connection in place we can flip the LCD into its location and begin securing it down with its four Phillips screws at all four corners.

with your LCD screwed down and secured we can move on to our touch screen lifting it up into position, when you're doing this install your replacement touch screen is going to have all new adhesive, you might want to be on the lookout for a little bit of debris or maybe old adhesive on the base of the unit, before securing your touch screen down.

go ahead and flip the touch screen down for the final piece of assembly, and it's not necessary but i find it useful to reheat up the adhesive when you're securing the touch screen down to the base of the ipad to assist with adhesion.

We do not produce the mobile phone lcd screen, we only do recycle,repair swap and lcd screen wholesale.

Surprise, now ,register on our website https://www.lcdone.com, with the referral code: jackie20160727, you can get the free shipping for your first order.

2016/07/24

What do you mean OEM pink iPhone screens?

We do cracked iPhone screens swap. There are offices in Tennessee.

When i send the testing reports to our clients for the first time, it will always happen to me that what do you mean OEM pink screens in the testing report?

Yes, did you ever hear about iPhone OEM pink color LCD screens?

Pink screens are all the screens with QR code Engraved (no sticker) on the metal cover of the ribbon cable, with single line serial numbers. Usually, parts of them are hard to find out the pink mark and a few of them also are still good, but the pink will show up after refurbishment or after a period of time.

Do you get it? But don't worry, you can never get pink iPhone screens from us as pink color won't happen again by our machines.

We do not produce the mobile phone lcd screen, we only do recycle,repair swap and lcd screen wholesale.

Surprise, now ,register on our website https://www.lcdone.com, with the referral code: coco20160722, you can get the free shipping for your first order.

2016/07/21

Did you really get the OEM iPhone lcd screens?

"Hi Coco, why do your iPhone lcd screens are so expensive? For OEM iPhone 6 screens, just $30/pcs from US location." One guy text me and complain about our screens price today. But after i told the difference, he is very happy to get our screens.

Please don't let the term OEM fool you! $30/pcs for OEM iPhone 6? Those screens must be with a Chinese knockoff LCD and cheap low grade glass, but it's sold as OEM. As we buy cracked OEM iPhone 6 for $30.

How do you know if OEM iPhone 6 lcd screens?

Are there Apple logos on both the LCD screen flex and digitizer's flex cables? If there are, then congratulations! You have 100% OEM iPhone 6 LCD screens and digitizer assembly.

About the glass, not original glass from us, but almost as gorilla glass, quality as good as Apple glass, it's more tough and resistant to cracking.

Any more questions,why not try samples first, DHL free shipping.

We do not produce the mobile phone lcd screen, we only do recycle,repair swap and lcd screen wholesale.

Surprise, now ,register on our website https://www.lcdone.com, with the referral code: coco20160722, you can get the free shipping for your first order.

2016/07/18

video about how to replace ipad 2 lcd screen and digitizer assembly - LCDONE

we're going to show you how to change a series of parts out of the ipad 2 before doing, so we need to show you how to peel back our front touch screen, about two inches from the bottom on the left hand side of the unit.

we need to recognize that our ribbon cable for that front touch screen is in this general location, and just to the right of the home button is where our Wi-Fi antenna is at here to the bottom side of the touch screen.

so when we peel back our front touch screen, let's be mindful of these two pieces as to not cause irreversible damage, time to begin our entry into the ipad.

let's first start with our heat gun or blow dryer and begin to soften up the adhesive around the perimeter about one to two minutes of the heat should suffice.

our triangle opening tools, let's bring in our plastic opening tool and you'll also notice in this video that we use a simple razor blade.

we found that the razor blade is the easiest way to start the separation of the touch screen from the ipad bezel, which your separation started with the razor blade we can then bring in our plastic opening tool, to continue the separation all the way around the perimeter of the ipad.

as we work the opening on one side, you'll notice we fit a triangle opening tool into the gap. this is to keep the adhesive from coming back in touch with itself, as we work ourselves all the way around the unit.

notice as we go from each side again another triangle tool goes into place.

you'll notice in our video we used our spider to continue peeling the Wi-Fi antenna off the bottom side of the touch screen before completely opening up the unit.

when we finally did crack the unit open, we peeled the touch screen back as if it was a book to make sure we didn't put too much tension on its ribbon wire and cause damage to it.

notice the LCD and how it's mounted with 4 Phillips screws.

let's now take our small phillips screwdriver and remove these screws, so that we can free the LCD for removal. prying up lightly with our plastic opening tool and peeling out the LCD.

we can lay it now on top of our touch screen so that we can disconnect the cable from the motherboard, our LCD cable has a locking socket, it's the metal style lever that needs to be flipped up in a 90 degree fashion. with the lock released, we can now remove the ribbon cable and lift the LCD completely from the ipad.

let's bring our attention now to the touch screen connections, we have two locking sockets we need to flip the tabs on and release, and then we can remove the ribbon cable, and remove the touch screen completely from the ipad.

let's go ahead and do the reassemble of our iPad 2, you'll notice that we've laid down new adhesive strips for our replacement touch screen.

stands out new adhesive strips with all of our replacement parts with the adhesive strips you're going to want to utilize either scissors or a razor blade to go ahead and cut your strips - sighs and lay them in preparation for your reassemble.

we want to go ahead and start our reassemble by positioning our touch screen into place and maneuvering the ribbon cable, in an area so that we can reconnect it to our mother board.

there's two connections here for this cable let's slide them into their locking socket and then flip are locking tab down to secure its connection, with our touch screen securely connected we can now bring in our LCD display, let's lay it on top of our touch screen so that we can maneuver it's ribbon cable to the motherboard, and connected in a similar fashion as we did the touch screen.

with the LCD connected to the motherboard we can go ahead and flip it over into the body of our iPad, and secure it down with its four Phillips screws one at each corner. now before we flip over our touch screen and finalize our reassemble, make sure we clean between the touch screen and the LCD as once we secure it down with adhesive it will be inaccessible for future cleaning.

we can now begin to remove our covers on our new adhesive strips, with our new adhesive strips exposed we can go ahead and flip over the touch screen now, and maneuver it into place to secure that touch screen go ahead and firmly press down on it all the way around the unit making sure it's secure and sealed.

LCDONE,a high-tech company providing the solutions for the mobile phone broken glass screen,including iPhone LCD recycling,Samsung Galaxy LCD recycling,iPhone LCD screen repair swap,Samsung Galaxy LCD screen repair swap,iPhone LCD screen wholesale,iPad touch screen wholesale and mobile phone accessories.

We do not produce the mobile phone lcd screen, we only do recycle,repair swap and resell lcd screen.

Surprise, now ,register on our website https://www.lcdone.com, with the referral code:jackievon001, you can get a $5 gift certificate. And if you submit order on our website, we will send the free iPhone Repair Tools Kits to you together at the time of delivery.

video about how to replace ipad mini 4 lcd screen and digitizer assembly

Step 1 Power down your 4th generation iPad Mini tablet.

Step 2 Apply heat to the top corner of the iPad Mini 4 to soften the adhesive. Use the suction cup and precision knife to create separation between the display assembly and rear case. Insert a plastic triangle opening tool and start slicing through the adhesive. Take your time and apply firm, constant force and additional heat. The iPad Mini 4 display assembly is a much tighter fit than most devices and is held down with a good amount of adhesive. With the adhesive softened, our tried-and-true method of suction cup and triangle opening tools will prevail. The iPad Mini 4 screen is still connected to the iPad by several cables, so don’t try to remove it entirely just yet.

Step 3 Remove the following 4 Phillips screws securing the metal bracket to the motherboard. Remove the metal bracket and disconnect the battery, LCD and digitizer ribbon cables.

Step 4 Release the ZIF connector and carefully slide out the iPad Mini 4 home button assembly cable. The home button bracket is held in place with two gobs of adhesive. Apply heat to soften the adhesive. Use a combination of the spudger and tweezers to pry up the iPad's home button cable and remove the home button assembly and bracket from the front panel.

LCDONE,a high-tech company providing the solutions for the mobile phone broken glass screen,including iPhone LCD recycling,Samsung Galaxy LCD recycling,iPhone LCD screen repair swap,Samsung Galaxy LCD screen repair swap,iPhone LCD screen wholesale,iPad touch screen wholesale and mobile phone accessories.

We do not produce the mobile phone lcd screen, we only do recycle,repair swap and resell lcd screen.

2016/07/14

The iPhone 7 will be equipped with sapphire screen

On November 8, 2015, a news blackout linking the Apple iPhone 7, conference will be in the middle of September 2016.

Apple says it will launch a 5.5 inch screen, 3 gb of memory, 14 million pixels, 256 gb and 3100 mah battery capacity of the iPhone 7 version. iPhone 7 also may have a 3d touch technology, flexible displays, and many cool technology such as waterproof and fast charging.

The iPhone 7 screen will use a new sapphire glass, the glass has strong resistance, scratch resistance, anti glare. Before a few iPhone models are adopted the gorilla glass, sapphire, more resistant than corning gorilla glass, more wear-resisting.

LCDONE,a high-tech company providing the solutions for the mobile phone broken glass screen,including iPhone LCD recycling,Samsung Galaxy LCD recycling,iPhone LCD screen repair swap,Samsung Galaxy LCD screen repair swap,iPhone LCD screen wholesale,iPad touch screen wholesale and mobile phone accessories.

We do not produce the mobile phone lcd screen, we only do recycle,repair swap and resell lcd screen.

2016/07/07

How to distinguish the iPhone LCD working normally

The iPhone 6 display screen, can be divided into three layers, the first layer called glass screen on the outside, the other two layers generally referred to as the inside screen, including touch screen and LCD screen. The inside and outside screen is together, cannot be separated by hand, need to use the factory equipment and technology level. Work environment must be well protected against dust, anti-static, need cutting machine screen separation of inside and outside, still need the new pressure screen machine screen and screen agglutination.

To most of the friends, when iPhone display screens broken, maybe only the outside glass screen broken, the inside LCD and touch screen is working normal.

So how to distinguish the iPhone LCD working normally? Check whether iPhone touch screen sensitive, look at the display for flower screen (mainly in cylindrical stripes), presence of color (red or purple at most). If not, congratulations, fractured just display on the outside, and inside the screen is normal.

LCDONE,a high-tech company providing the solutions for the mobile phone broken glass screen,including iPhone LCD recycling,Samsung Galaxy LCD recycling,iPhone LCD screen repair swap,Samsung Galaxy LCD screen repair swap,iPhone LCD screen wholesale,iPad touch screen wholesale and mobile phone accessories.

We do not produce the mobile phone lcd screen, we only do recycle,repair swap and resell lcd screen.

Why iPhone 6 display screen is so easy to be broken

Since iPhone 6 / 6 plus appeared on the market while popular with consumers, but the resulting ground display screen event, really let the consumers around the world be worried.

Because of iPhone 6 is 2.5d surface design, the screen glass feels better with a drop of water surface, but sacrificed the anti-throw performance at the same time.

It is more crucial iPhone 6 rear camera design is outstanding than the fuselage, flat on level table, is not smooth. This feature more increased the imbalance of iPhone 6 mobile phone fell down force.

The last place, the bane of iPhone 6 using the corning gorilla glass as the screen display on the outside. The glass performance is very good, very strongly pervious to light quality and intensity, key method didn't cut with a knife. But too brittle just, gently touch is broken.

So iPhone 6 earned the world's most fragile electronic products in 2014.

LCDONE,a high-tech company providing the solutions for the mobile phone broken glass screen,including iPhone LCD recycling,Samsung Galaxy LCD recycling,iPhone LCD screen repair swap,Samsung Galaxy LCD screen repair swap,iPhone LCD screen wholesale,iPad touch screen wholesale and mobile phone accessories.

We do not produce the mobile phone lcd screen, we only do recycle,repair swap and resell lcd screen.

2016/06/30

For Apple iPhone 4S LCD Screen Replacement And Digitizer Assembly with Frame - OEM Original Quality Grade : LCDONE, Providing iPhone LCD Recycling,iPhone LCD Repair Swap and iPhone LCD Screen Replacement

For Apple iPhone 4S LCD Screen Replacement And Digitizer Assembly with Frame - OEM Original Quality Grade : LCDONE, Providing iPhone LCD Recycling,iPhone LCD Repair Swap and iPhone LCD Screen Replacement

2016/06/21

Apple confirmed that iPhone will match the OLED screen in 2018

According to the Nikkei Asian Review reports, Apple has informed its supply chain vendors, all the iPhone will switch to OLED screen in 2018.

Reported that in 2017, iPhone will be the part of the first import the OLED, and before the news that Apple next year will be used on at least an iPhone OLED, and perhaps even curved surface screen version.

In order to compete for this super order, Samsung Display, LG Display, Japan Display (JDI) three panel giants are aggressively courted Apple, at the same time to extend the OLED production capacity.

Samsung this year will invest 8 trillion won, the capacity of the OLED to expand by 50%, which has the capability of annual output of 500 million the OLED panel. Samsung shipped 320 million smartphones in 2015, so the OLED panel capacity must win enough external orders.

LG plans in the next few years out of 10 trillion won, improve the production ability of mobile phone, TV, OLED panel, JDI is planning the next year, 50 billion yen, starts the new OLED production line.

LCDONE,a high-tech company providing the solutions for the mobile phone broken glass screen,including iPhone LCD recycling,Samsung Galaxy LCD recycling,iPhone LCD screen repair swap,Samsung Galaxy LCD screen repair swap,iPhone LCD screen replacement,iPad touch screen replacement and mobile phone accessories.

We do not produce the mobile phone lcd screen, we only do recycle,repair swap and resell lcd screen.

Surprise, now ,register on our website https://www.lcdone.com, with the referral code : jackievon001, you can get a $5 gift certificate. And if you submit order on our website, we will send the free iPhone Repair Tools Kits to you together at the time of delivery.

2016/06/08

How to replace iphone 6 plus lcd screen and digitizer assembly - LCDONE

Step 1. If possible, power down your iphone 6 plus, in this example the LCD is damaged, so we do not have that option.

Step 2. Remove the two bottom three four millimeter pentalobe screws, located next to the Lightning connector.

Step 3. Place a suction cup near the home button, while applying firm constant force use the plastic triangle opening tool to work around the display assembly and separated from the iphone 6 plus rear case. the display assembly is still connected to the iphone by several cables, so don't try to remove it entirely just yet.

Step 4. Remove the following five phillips screws securing the metal bracket to the motherboard. now use the fine tip curved tweezers to remove the metal bracket and disconnect the LCD digitizer and front camera and proximity sensor cables.

Step 5. Remove the following three Phillips screws securing the earpiece speaker bracket to the display assembly, with the tweezers remove the bracket and then the earpiece speaker.

Step 6. Carefully pry up the front camera and proximity sensor ribbon cable away from the display assembly.

Step 7. Remove the following two Phillips screws securing the home button metal bracket in place. disconnected peel the home button ribbon cable away from the display assembly. remove the home button assembly.

Step 8. Remove the eighth Phillips screws that secure the LCD shield plate to the iphone 6 plus display assembly, peel updated he civ securing the home button cable connector to the front panel and remove the LCD shield played.

LCDONE,a high-tech company providing the solutions for the mobile phone broken glass screen,including iPhone LCD recycling,Samsung Galaxy LCD recycling,iPhone LCD screen repair swap,Samsung Galaxy LCD screen repair swap,iPhone LCD screen replacement,iPad touch screen replacement and mobile phone accessories.

We do not produce the mobile phone lcd screen, we only do recycle,repair swap and resell lcd screen.

Surprise, now ,register on our website https://www.lcdone.com, with the referral code : jackievon001, you can get a $5 gift certificate. And if you submit order on our website, we will send the free iPhone Repair Tools Kits to you together at the time of delivery.

2016/06/05

How to replace iphone 5 lcd screen and digitizer assembly - LCDONE

1.Remove the two pentalobe screws that are located on both sides of the lightening connector port which is on the bottom of your iPhone 5.

2.Place the suction cup on the display assembly near the home button. Use the plastic opening tool to separate the display assembly from the case of the iPhone 5.With the suction cup, pull up on the display assembly while holding the outside frame of the iPhone 5 down. Near the home button, in the left corner of the iPhone 5, will be an area that will expose enough space to get in the plastic opening tool.

3.Once you have the opening tool in the space, pry the display assembly from the iPhone 5. Work your way around the iPhone 5 until it is completely separated and can be pulled back with the suction cup.

4.Peel back the display assembly to expose the metal cover that secures the display assembly flex cables.Locate and remove the three small Phillips screws (#00) that secure the metal cover. Remove the cover from the iPhone 5.

5.There are a series of connections that will require the plastic opening tool or spudger to pry up and remove.The first of these connections is for the front-facing camera and sensor flex cable.

6.The touch screen/front panel cable is next. Gently pry up and out to disconnect the cable.

7.The last connection is the LCD cable. Once the cable is disconnected, remove the entire display assembly from the iPhone 5.

8.Locate and remove the two small Phillips screws (#00) that secure the cover to the earpiece speaker. Remove the cover from the iPhone 5.When the cover for the earpiece speaker is removed, lift the speaker up and away from the iPhone 5.

9.Using the flat end of the spudger, maneuver the front-facing camera and sensor flex cable away from the iPhone 5.

10.Locate and remove the two small Phillips screws (#00) that secure the home button assembly.Remove the home button assembly from the iPhone 5.

11.The actual home button is secured by a small amount of adhesive. Use the spudger to remove the home button from the display assembly.

12.Locate and remove the six small Phillips screws (#00) that secure the LCD shield to the display assembly.Once the Phillips screws are removed, lift the shield up and away from the iPhone 5.

13.Locate and remove the three small Phillips screws (#00) that secure the battery connector and lightning connector covers.Once the screws are removed, take the metal covers off of the iPhone 5.

14.Utilize the spudger to pry up and disconnect the battery connector from the motherboard.

15.Using the plastic pull-tab and the spudger, remove the battery from the case of the iPhone 5.

16.Locate and remove the two small Phillips screws (#00) that secure the top motherboard bracket.Once the screws have been removed, lift the bracket up and away from the iPhone 5.

17.For the next few steps, the spudger will be utilized to disconnect several connections. This will allow you to remove the iPhone’s motherboard.Remove the LED flash from the motherboard by pulling it up and away from the assembly.

18.The next connection is the for audio/volume controls. Lift up and pry it from the socket to remove the plug.

19.An interconnecting cable is next to be removed. Lift up and pry it from the socket to remove the cable.

20.There is another interconnection cable that will need to be disconnected as well.

21.The last plug is the lightning port assembly. It is located on bottom of the motherboard.

22.One of the two antenna connections is on the front of the board. Pry up and remove the wire from its location.Maneuver the headphone jack out of its housing and prepare to remove it in the follow steps.

23.Before removing the motherboard, use the SIM card removal tool, or a paper clip, to remove the SIM card tray from the iPhone 5.

24.Locate and remove the two small Phillips screws (#00) inside the top portion of the iPhone 5 case.

25.Next, locate and remove the two small Phillips screws (#00) and the three standoff screws. The three standoff screws secure the motherboard into the iPhone 5. You will need a small flathead screwdriver to remove these screws.

26.Remove the second antenna plug on the bottom of the motherboard. Now, you can carefully lift the motherboard up and out of the iPhone 5.

27.Locate and remove the two small Phillips screws (#00) that secure the rear-facing camera connection to the motherboard.With these screws removed, take the plate off that was securing this plug.

28.Using the spudger, gently pry up the connection to remove the rear-facing camera from the motherboard.

29.Locate and remove the seven small Phillips screws (#00) that secure the lightning connector and loudspeaker assembly inside the case of the iPhone.

30.Use the flat end of the spudger to break free the adhesive that secures the lightning connector and loudspeaker assembly inside the case of the iPhone 5.Remove these two parts from the iPhone 5.

31.With the lightening connector and loudspeaker assembly free from the case, use the spudger to separate the two units from each other. They are held together with a small amount of adhesive.

32.Locate and remove the three small Phillips screws (#00) that secure the vibrator in the corner of the iPhone 5 case.Remove the vibrator from the iPhone 5.

33.There are three additional small Phillips screws (#00) that secure the volume and silent switch assembly on the side of the iPhone 5 case.

34.Use the spudger to peel out the WiFi and Bluetooth Antenna Flex Cable from the iPhone 5 case.

35.Locate and remove the last small Phillips screw(#00) that secures the power and volume button assembly in the iPhone 5.

36.Use the flat end of the spudger to remove the ribbon cable for the volume, silent switch, and power buttons from the iPhone 5.

LCDONE,a high-tech company providing the solutions for the mobile phone broken glass screen,including iPhone LCD recycling,Samsung Galaxy LCD recycling,iPhone LCD screen repair swap,Samsung Galaxy LCD screen repair swap,iPhone LCD screen replacement,iPad touch screen replacement and mobile phone accessories.

We do not produce the mobile phone lcd screen, we only do recycle,repair swap and resell lcd screen.

Surprise, now ,register on our website https://www.lcdone.com, with the referral code : jackievon001, you can get a $5 gift certificate. And if you submit order on our website, we will send the free iPhone Repair Tools Kits to you together at the time of delivery.

2016/06/02

How to replace iphone 4 lcd screen and digitizer assembly -LCDONE

1.Let’s begin to disassemble the iPhone 4 byremoving the SIM card tray. Use the SIM cardejection tool or a paperclip to eject and removethe tray from the iPhone 4.

2.Remove the two pentalobe screws on either sideof the dock port connector with the iPhone 5-PointPentalobe screwdriver.

3.Grip the back cover of the phone and push upward about 1/8 of an inch to remove the back cover from the iPhone 4.

4.There is a cover over the battery connector. Todisconnect the cover, locate and remove the onePhillips screw (#00) that secures it in place.When the screw is removed, use the spudger togently pry up the connection releasing it from themotherboard.

5.To remove the battery, use the plastic openingtool and the pull-tab to pry the battery out of itslocation. It is secured by a small amount ofadhesive.

6.To begin the process of removing the motherboard from the iPhone, locate and remove the two Phillips screws (#00) that secure the speaker assembly’s connection into the iPhone 4. Next, peel back the ribbon cable.

7.Once you peel back the speaker assembly‘s ribboncable, one of two Phillips screws (#00) that need tobe removed will be revealed. Use the appropriatescrewdriver to remove both screws.You will also need to use the spudger to pry theplugged connection from the corner of themotherboard.

8.Remove the two Phillips screws (#00), located oneither side of the assembly, that secure the dockport into the iPhone.The ribbon cable for the home button has a lockingsocket. Flip the tab on the locking socket to releaseand remove the ribbon cable from the connection.

9.With the securing screws and ribbon cableremoved from the assembly, use the spudger to liftthe dock port assembly out of the bottom of theiPhone.

10.Locate and remove the seven Phillips screws(#00) that secure the connection plate and vibratemotor into the iPhone.You can now remove the vibrate motor from theiPhone 4.

11.With the screws removed from the connectionplate, use the tweezers to lift the protectionplate out of the iPhone 4.

12.A total of six connections need to be pried up fromthe motherboard. Use the tweezers to remove theconnections.With all of the connections lifted from themotherboard, pry the rear-facing camera out of itshousing and remove it from the iPhone 4.

13.Locate and remove the final two screws securingthe motherboard into the body of the iPhone.Remove the single Phillips screw (#00).Next, remove the standoff with a small flat heador slotted screwdriver.

14.At this point all connections and securing screwsare removed from the motherboard. Themotherboard is free, so remove the motherboardfrom of the iPhone 4.

15.There is a metal clip that secures the front-facingcamera into the iPhone. Use the tweezers to lift theclip from the iPhone.You can now remove the front-facing camera fromthe iPhone.

16.The earpiece speaker is secured with a smallamount of adhesive. Use the tweezers to lift theearpiece speaker out of the iPhone.

17.Locate and remove the four Phillips screws (#00)that secure the volume button assembly into theside of the iPhone.

18.A ribbon cable connects the headphone jack andvolume button assembly. When prying theheadphone jack out of it’s housing, be mindful ofthis connection because it can be easily damaged.With the headphone jack peeled from the phone,you will see the final Phillips screw (#00) thatneeds to be removed. Remove this screw to freethe entire assembly from the iPhone.Remove the headphone jack and volume buttonassembly from the iPhone 4.

19.Locate and remove the ten Phillips screws (#00)that secure the display assembly into the body ofthe iPhone.

20.The display assembly is free to be lifted from theiPhone. If necessary, utilize the plastic openingtool to pry the display away from the iPhone 4.

21.To remove the home button, use the tweezers tomaneuver the ribbon cable for the home buttonaway from the iPhone.You can now remove the home button from theiPhone 4.

22.Locate and remove the two Phillips screws (#00)that secure the power button into the top of theiPhone.

23.The power button is connected to a proxy sensorand microphone via ribbon cable, when removingthe assembly be cautious not to damage the ribboncable.You can now, carefully, remove the power buttonassembly from the iPhone 4.

LCDONE,a high-tech company providing the solutions for the mobile phone broken glass screen,including iPhone LCD recycling,Samsung Galaxy LCD recycling,iPhone LCD screen repair swap,Samsung Galaxy LCD screen repair swap,iPhone LCD screen replacement,iPad touch screen replacement and mobile phone accessories.

We do not produce the mobile phone lcd screen, we only do recycle,repair swap and resell lcd screen.

Surprise, now ,register on our website https://www.lcdone.com, with the referral code : jackievon001, you can get a $5 gift certificate. And if you submit order on our website, we will send the free iPhone Repair Tools Kits to you together at the time of delivery.

2016/06/01

How to replace iphone 5c lcd screen and digitizer assembly

1.To begin disassembling the iPhone 5c, locate and remove the two pentalobe screws on either side of the lightning dock connector port on the bottom of the iPhone.

2.Next, put the suction cup close to the home button on the display assembly side of the iPhone. While holding the outside of the iPhone down, use the suction cup to pull the display assembly away from the rear case. The left corner, on the home button side of the iPhone 5c, has an area that will expose enough space to insert the plastic opening tool. Use the plastic opening tool to separate the display assembly from the rear case/housing of the iPhone.

3.After lifting up the display assembly, you will see a metal cover that secures the display assembly cables. Locate and remove the four Phillips screws (#00) that secure the cover, and then remove the cover from the iPhone 5c.

4.Utilize the plastic opening tool or spudger to pry up the series of three connections for the display assembly and front-facing camera. You can now remove the display assembly from the iPhone 5c.

5.Locate and remove the two Phillips screws (#00) that secure the back plate for the home button assembly.

6.Using the flat end of the spudger or the tweezers, peel up the ribbon cable connection for the home button. It is secured in place with a small amount of adhesive. You can now remove the home button assembly from the iPhone 5c.

7.Locate and remove the two small Phillips screws (#00) securing the metal clip over the earpiece speaker.

8.Pry up the clip from its location with a pair of tweezers to free the speaker assembly and remove it from the iPhone 5c.

9.The front-facing camera assembly is a series of compo-nents that you need to pry up from their housing. The assembly is also held down by a sticker and adhesive.You can now remove the front-facing camera assembly from the iPhone 5c.

10.Locate and remove the two Phillips screws (#00) that secure the battery connector’s cover. Next, gently pry the connector up to release it from the motherboard.

11.Use the spudger or the plastic opening tool to pry the battery from the adhesive securing it to the iPhone. You can now remove the battery from the iPhone 5c.

12.Locate and remove the seven Phillips screws (#00) that secure the loudspeaker and lightning port assembly (marked with white dots). Next, locate and disconnect the coaxial antenna plug (circled in orange). Now, locate and disconnect the connector for the lightning port assembly (rectangle in orange).

13.There is a small ribbon wire connection that is adhered to the loudspeaker. Peel up this contact to free the loudspeaker for removal from the iPhone 5c.

14.Use the spudger to maneuver and pry up the lightning port assembly and remove it from the bottom of the iPhone.

15.Locate and remove the two Phillips screws (#00) that secure the rear-facing camera and then lift it out of the iPhone.

16.Locate and remove the two Phillips screws (#00) that secure the vibrator to the body of the iPhone. You can now remove the vibrator motor from the iPhone 5c.

17.Use the SIM card removal tool, or a paper clip, to remove the SIM card tray from the side of the iPhone.

18.Locate and remove the three Phillips screws (#00) that secure the motherboard into the phone (white dots mark them). Next, locate and remove the two standoffs with the small flathead screwdriver. The standoffs secure the mother-board to the iPhone (blue dots mark them). Now, locate and disconnect the coaxial antenna plug (circled in orange).

19.With all screws and connections removed, the mother-board is now free. Maneuver the motherboard out of its location and lift it from the iPhone 5c.

20.Locate and remove the six Phillips screws (#00) that secure the power & volume button assembly to the motherboard (white dots mark them). Now, locate and remove the one standoff with the small flathead screwdriver (blue dot marks it).

21.A small amount of adhesive is still securing the power and volume button assembly to the iPhone. Use the spudger or the tweezers to peel up and remove the assembly from the iPhone 5c.

LCDONE,a high-tech company providing the solutions for the mobile phone broken glass screen,including iPhone LCD recycling,Samsung Galaxy LCD recycling,iPhone LCD screen repair swap,Samsung Galaxy LCD screen repair swap,iPhone LCD screen replacement,iPad touch screen replacement and mobile phone accessories.

We do not produce the mobile phone lcd screen, we only do recycle,repair swap and resell lcd screen.

Surprise, now ,register on our website https://www.lcdone.com, with the referral code : jackievon001, you can get a $5 gift certificate. And if you submit order on our website, we will send the free iPhone Repair Tools Kits to you together at the time of delivery.

2016/05/30

how to replace iphone 6s plus lcd screen and digitizer assembly - LCDONE

Warning: You are performing this repair at your own risk,We claim no responsibility for any damages that might occur

To perform this DIY repair, you will need the following tools: Small Phillips Screwdriver,iPhone 5-Point Pentalobe Screwdriver,iSesamo Opening Tool,Suction Cup,Fine Tip Curved Tweezers.

Step 1 Power down your iPhone 6s Plus.

Step 2 Remove the two bottom 3.4 mm Pentalobe screws located next to the lightning connector.

Step 3 Place a suction cup near the home button and pull the iPhone 6s Plus display assembly away from the rear case. Use the iSesamo opening tool to slice through the adhesive and help carefully separate the display assembly from the rear case. Take your time and apply firm, constant force. The display assembly is a much tighter fit than most devices and is held down with adhesive. The display assembly is still connected to the iPhone by several cables, so don’t try to remove it entirely just yet.

Step 4 Remove the following 5 Phillips screws securing the metal cover to the iPhone's motherboard. Now use the fine tip curved tweezers to disconnect the LCD, digitizer and front camera and proximity sensor cables.

Step 5 Remove the following 2 Phillips screws securing the home button metal bracket in place. Disconnect and peel the home button ribbon cable away from the display assembly. Remove the 6s Plus home button assembly.

Step 6 Remove the following 3 Phillips screws securing the earpiece speaker bracket to the display assembly. Remove the iPhone 6s Plus earpiece speaker.

Step 7 Gently pry the front camera and proximity sensor ribbon cable away from the display assembly.

Step 8 Remove the 7 Phillips screws that secure the LCD shield plate to the display assembly.

LCDONE,a high-tech company providing the solutions for the mobile phone broken glass screen,including iPhone LCD recycling,Samsung Galaxy LCD recycling,iPhone LCD screen repair swap,Samsung Galaxy LCD screen repair swap,iPhone LCD screen replacement,iPad touch screen replacement and mobile phone accessories.

We do not produce the mobile phone lcd screen, we only do recycle,repair swap and resell lcd screen.

Surprise, now ,register on our website https://www.lcdone.com, with the referral code : jackievon001, you can get a $5 gift certificate. And if you submit order on our website, we will send the free iPhone Repair Tools Kits to you together at the time of delivery.

Video about how to replace iphone se lcd screen - LCDONE

Warning: You are performing this repair at your own risk,We claim no responsibility for any damages that might occur

To perform this DIY repair, you will need the following tools: Plastic Triangle Opening Tool,Suction Cup,SIM Card Ejection Tool,Fine Tip Curved Tweezers,Professional Phillips Screwdriver,Professional iPhone Pentalobe Screwdriver.

Step 1 Power down your Apple iPhone SE smartphone.

Step 2 Remove the two bottom 3.4 mm Pentalobe screws located next to the iPhone SE lightning connector.

Step 3 Place a suction cup near the home button. While applying firm, constant force, use the plastic triangle opening tool to work around the display assembly and separate it from the iPhone SE rear case. Just like the iPhone 5s, lurking beneath the iPhone SE display is the touch ID cable. Do not pull the display up too far without first removing the bracket and disconnecting the cable. The display assembly is still connected to the iPhone by several cables, so don’t try to remove it entirely just yet.

Step 4 Remove the following 4 Phillips screws securing the metal bracket to the motherboard. These screws are different sizes, so be sure to remember where they go. Use the fine tip curved tweezers to remove the metal bracket and disconnect the iPhone SE LCD, digitizer, and front camera and proximity sensor cables.

Step 5 Remove the following 3 Phillips screws securing the home button cable and the metal bracket in place. Remove the metal bracket and then with the tweezers peel the iPhone SE home button away from the display assembly.

Step 6 Remove the following 7 Phillips screws. With the tweezers remove the metal clip and then the iPhone SE earpiece speaker.

Step 7 Gently pry the front camera and proximity sensor ribbon cable away from the display assembly. Now, if necessary, separate the iPhone SE front-facing camera and proximity sensor cable from the LCD shield plate.

LCDONE,a high-tech company providing the solutions for the mobile phone broken glass screen,including iPhone LCD recycling,Samsung Galaxy LCD recycling,iPhone LCD screen repair swap,Samsung Galaxy LCD screen repair swap,iPhone LCD screen replacement,iPad touch screen replacement and mobile phone accessories.

We do not produce the mobile phone lcd screen, we only do recycle,repair swap and resell lcd screen.

2016/05/27

How to replace iphone 4s lcd screen and digitizer assembly

Step 1. Before disassembling your iPhone, be sure it is powered off. Your iPhone 4s rear cover may have either two #000 Phillips screws or Apple's 5-Point "Pentalobe" screws (second image). Check which screws you have, and ensure you also have the correct screwdriver in order to remove them.

LCDONE iPhone 4s LCD Screen Replacement Installation 1

Step 2. Push the rear panel toward the top edge of the iPhone.

LCDONE iPhone 4s LCD Screen Replacement Installation 2

Step 3. Pinch the rear panel with your fingers and lift it away from the iPhone. Alternatively, use aSmall Suction Cup.

LCDONE iPhone 4s LCD Screen Replacement Installation 3

Step 4. Remove the single 2.5 mm Phillips screw securing the battery connector to the logic board.

LCDONE iPhone 4s LCD Screen Replacement Installation 4

Step 5. Use a plastic opening tool to gently pry the battery connector up from its socket on the logic board.Remove the metal clip covering the antenna connector.

LCDONE iPhone 4s LCD Screen Replacement Installation 5

Step 6. Use the clear plastic pull tab to gently lift the battery out of the iPhone.Remove the contact clip from the iPhone.

LCDONE iPhone 4s LCD Screen Replacement Installation 6

Step 7. Use a SIM card eject tool or a paperclip to eject the SIM card and its holder.Remove the SIM card and its holder.

LCDONE iPhone 4s LCD Screen Replacement Installation 7

Step 8. Remove the following two screws: One 1.2 mm Phillips One 1.6 mm Phillips Remove the thin steel dock connector cable cover from the iPhone.

LCDONE iPhone 4s LCD Screen Replacement Installation 8

Step 9. Use an iPod opening tool to gently pry the dock cable connector up off the logic board from both short ends of the connector.

LCDONE iPhone 4s LCD Screen Replacement Installation 9

Step 10. Carefully peel the dock ribbon cable off the logic board and the lower speaker enclosure.

LCDONE iPhone 4s LCD Screen Replacement Installation 10

Step 11. Use a plastic opening tool to pry the lower antenna connector up off its socket on the logic board.

LCDONE iPhone 4s LCD Screen Replacement Installation 11

Step 12. Remove the 1.9 mm Phillips screw securing the bottom of the logic board to the inner case.

LCDONE iPhone 4s LCD Screen Replacement Installation 12

Step 13. Remove the following five screws securing the Wi-Fi antenna to the logic board: One 2.3 mm Phillips Two 1.6 mm Phillips One 1.4 mm Phillips One 4.8 mm Phillips

LCDONE iPhone 4s LCD Screen Replacement Installation 13

Step 14. Use an iPod opening tool to slightly lift the top edge of the Wi-Fi antenna away from the logic board. Use the tip of a spudger to pull the Wi-Fi retaining clips away from the inner frame. Remove the Wi-Fi antenna from the iPhone. Make sure you don't lose the metal clips on the top of the cover where the 4.8mm screw attaches or the 4.8mm screw. That's the primary reason for abnormal Wi-Fi performance after the reassembly.

LCDONE iPhone 4s LCD Screen Replacement Installation 14

Step 15. Use an iPod opening tool to carefully lift the rear camera connector up off its socket on the logic board. Remove the rear camera.

LCDONE iPhone 4s LCD Screen Replacement Installation 15

Step 16. Remove the small circular white sticker (warranty sticker and water indicator) covering the screw near the battery pull tab. Remove the 2.4 mm Phillips screw that was hidden underneath the sticker.

LCDONE iPhone 4s LCD Screen Replacement Installation 16

Step 17. Use the edge of a plastic opening tool to gently pry the following connectors up and out of their sockets on the logic board: Digitizer cable (pry from bottom) LCD cable (pry from bottom) Headphone jack/volume button cable (pry from top) Top Microphone/sleep button cable (pry from top) Front camera cable (pry from top)

LCDONE iPhone 4s LCD Screen Replacement Installation 17

Step 18. Use a small flathead screwdriver to remove the 4.8 mm standoff near the headphone jack.When reassembling the motherboard, ensure that its edge sits under the circled standoff, otherwise the screws will not fit. When reassembling ensure that the small rubber spacer attached to the top of the motherboard is in place. Without this part the motherboard could damage the ribbon cables around it.

LCDONE iPhone 4s LCD Screen Replacement Installation 18

Step 19. Carefully remove the logic board from the iPhone, minding any cables that may get caught.

LCDONE iPhone 4s LCD Screen Replacement Installation 19

Step 20. Remove the single 2.4 mm Phillips screw securing the speaker enclosure to the side of the inner frame.

LCDONE iPhone 4s LCD Screen Replacement Installation 20

Step 21. Remove the speaker enclosure from the iPhone.

LCDONE iPhone 4s LCD Screen Replacement Installation 21

Step 22. Remove the following two screws securing the vibrator to the inner frame: One 6 mm Phillips One 1.4 mm Phillips Remove the vibrator from the iPhone.

LCDONE iPhone 4s LCD Screen Replacement Installation 22

Step 23. Remove the 1.5 mm Phillips screw securing the front panel near the headphone jack.

LCDONE iPhone 4s LCD Screen Replacement Installation 23

Step 24. Remove the three large-headed 1.5 mm Phillips screws along the volume button side of the iPhone.

LCDONE iPhone 4s LCD Screen Replacement Installation 24

Step 25. Remove the 1.5 mm Phillips screw near the lower microphone.

LCDONE iPhone 4s LCD Screen Replacement Installation 25

Step 26. Remove the 1.5 mm Phillips screw near the dock connector ribbon cable.

LCDONE iPhone 4s LCD Screen Replacement Installation 26

Step 27. Remove the three large-headed 1.5 mm Phillips screws along the SIM card side of the iPhone.Remove the small-headed 1.5 mm Phillips screw near the rear camera.

LCDONE iPhone 4s LCD Screen Replacement Installation 27

Step 28. Carefully insert the edge of an iPod opening tool between the rubber bezel around the front glass panel and the steel inner frame. Do not attempt to insert the tool between the glass and the rubber bezel. Carefully pry the upper edge of the front panel assembly away from the steel inner frame.

LCDONE iPhone 4s LCD Screen Replacement Installation 28

Step 29. Slowly and gently lift the top edge of the front panel assembly away from the steel inner frame. Continue to rotate the front panel assembly away from the steel inner frame until it slowly begins to peel off the adhesive applied below the home button area. It may be easiest to insert a spudger at the top and work it around the edges, spreading gently as you go. Carefully pull the lower edge of the front panel assembly away from the steel inner frame.

LCDONE iPhone 4s LCD Screen Replacement Installation 29

Step 30. De-route the digitizer and LCD cables through the steel inner frame, and remove the display from the iPhone.When the front panel has been correctly installed, both the LCD and digitizer cables should be immediately next to one another and should be the same length, as shown in the second photo.During reassembly, do not touch the metallic area at the base of the LCD data cable, as this can cause problems with the LCD. If you do touch it accidentally, clean it gently with an alcohol wipe before continuing.

LCDONE iPhone 4s LCD Screen Replacement Installation 30

Step 31. Your replacement display may come with colored plastic film on the back of the LCD. If so, use the pull tab near the home button to peel the plastic film from the LCD before installing the new display in your iPhone. After reassembly, clean the touchscreen surface with an alcohol wipe prior to turning the iPhone back on. The alcohol helps dissipate any lingering static electricity, which can cause problems with the display. After reassembly, protect your new display from any scratches by installing a newscreen protector.

LCDONE iPhone 4s LCD Screen Replacement Installation 31

LCDONE,a high-tech company providing the solutions for the mobile phone broken glass screen,including iPhone LCD recycling,Samsung Galaxy LCD recycling,iPhone LCD screen repair swap,Samsung Galaxy LCD screen repair swap,iPhone LCD screen replacement,iPad touch screen replacement and mobile phone accessories.

We do not produce the mobile phone lcd screen, we only do recycle,repair swap and resell lcd screen.