we're going to show you how to change a series of parts out of the ipad 2 before doing, so we need to show you how to peel back our front touch screen, about two inches from the bottom on the left hand side of the unit.
we need to recognize that our ribbon cable for that front touch screen is in this general location, and just to the right of the home button is where our Wi-Fi antenna is at here to the bottom side of the touch screen.
so when we peel back our front touch screen, let's be mindful of these two pieces as to not cause irreversible damage, time to begin our entry into the ipad.
let's first start with our heat gun or blow dryer and begin to soften up the adhesive around the perimeter about one to two minutes of the heat should suffice.
our triangle opening tools, let's bring in our plastic opening tool and you'll also notice in this video that we use a simple razor blade.
we found that the razor blade is the easiest way to start the separation of the touch screen from the ipad bezel, which your separation started with the razor blade we can then bring in our plastic opening tool, to continue the separation all the way around the perimeter of the ipad.
as we work the opening on one side, you'll notice we fit a triangle opening tool into the gap. this is to keep the adhesive from coming back in touch with itself, as we work ourselves all the way around the unit.
notice as we go from each side again another triangle tool goes into place.
you'll notice in our video we used our spider to continue peeling the Wi-Fi antenna off the bottom side of the touch screen before completely opening up the unit.
when we finally did crack the unit open, we peeled the touch screen back as if it was a book to make sure we didn't put too much tension on its ribbon wire and cause damage to it.
notice the LCD and how it's mounted with 4 Phillips screws.
let's now take our small phillips screwdriver and remove these screws, so that we can free the LCD for removal. prying up lightly with our plastic opening tool and peeling out the LCD.
we can lay it now on top of our touch screen so that we can disconnect the cable from the motherboard, our LCD cable has a locking socket, it's the metal style lever that needs to be flipped up in a 90 degree fashion. with the lock released, we can now remove the ribbon cable and lift the LCD completely from the ipad.
let's bring our attention now to the touch screen connections, we have two locking sockets we need to flip the tabs on and release, and then we can remove the ribbon cable, and remove the touch screen completely from the ipad.
let's go ahead and do the reassemble of our iPad 2, you'll notice that we've laid down new adhesive strips for our replacement touch screen.
stands out new adhesive strips with all of our replacement parts with the adhesive strips you're going to want to utilize either scissors or a razor blade to go ahead and cut your strips - sighs and lay them in preparation for your reassemble.
we want to go ahead and start our reassemble by positioning our touch screen into place and maneuvering the ribbon cable, in an area so that we can reconnect it to our mother board.
there's two connections here for this cable let's slide them into their locking socket and then flip are locking tab down to secure its connection, with our touch screen securely connected we can now bring in our LCD display, let's lay it on top of our touch screen so that we can maneuver it's ribbon cable to the motherboard, and connected in a similar fashion as we did the touch screen.
with the LCD connected to the motherboard we can go ahead and flip it over into the body of our iPad, and secure it down with its four Phillips screws one at each corner. now before we flip over our touch screen and finalize our reassemble, make sure we clean between the touch screen and the LCD as once we secure it down with adhesive it will be inaccessible for future cleaning.
we can now begin to remove our covers on our new adhesive strips, with our new adhesive strips exposed we can go ahead and flip over the touch screen now, and maneuver it into place to secure that touch screen go ahead and firmly press down on it all the way around the unit making sure it's secure and sealed.
LCDONE,a high-tech company providing the solutions for the mobile phone broken glass screen,including iPhone LCD recycling,Samsung Galaxy LCD recycling,iPhone LCD screen repair swap,Samsung Galaxy LCD screen repair swap,iPhone LCD screen wholesale,iPad touch screen wholesale and mobile phone accessories.
We do not produce the mobile phone lcd screen, we only do recycle,repair swap and resell lcd screen.
Surprise, now ,register on our website https://www.lcdone.com, with the referral code:jackievon001, you can get a $5 gift certificate. And if you submit order on our website, we will send the free iPhone Repair Tools Kits to you together at the time of delivery.
No comments:
Post a Comment